Download Driver Cutting Plotter Jinka 1351 Link -

The Jinka 1351 cutting plotter driver download process involves identifying the correct source, ensuring compatibility with your operating system, and cautiously downloading and installing the driver. If specific links are not provided here, it's due to the potential for outdated information or the need for direct manufacturer support.

For the most accurate and up-to-date information, visiting the official manufacturer website or reaching out to their customer support is highly recommended.

To set up your Jinka 1351 cutting plotter, you must download the driver specific to your machine's model and connection type. Most Jinka drivers are hosted via official distribution links provided by regional manufacturers like Jinka Indonesia Official Driver Download Links

Drivers for the Jinka 1351 series vary depending on whether your model supports basic cutting or contour cutting. Jinka JK/XL Series (Cut Only): For standard models without contour cutting. Download via Google Drive Jinka XL Pro / XL 2022 (Semi-Auto Contour): For models supporting manual mark alignment. Download via Google Drive Jinka XL Pro V / PE PRO (Auto Contour): For high-end models with automatic sensors. Download via Google Drive CorelDRAW Plugins:

To cut directly from design software, you may need specific plugins like or the official Jinka CorelDRAW plugin. Installation Steps

Once you have the correct file, follow these steps to install: Extract the Files: Use WinRAR or 7-Zip to extract the downloaded folder. Run Setup: Locate and double-click or the USB driver installer. Port Configuration: Device Manager Look for the plotter under Ports (COM & LPT)

Ensure the COM port number in your cutting software (like Artcut, SignMaster, or Anycut) matches the one assigned by Windows. Connect Hardware:

Plug in the USB or Serial cable only after the driver installation is complete to allow Windows to recognize the device. Compatibility Notes Driver Jinka 1351 28 - Facebook

To successfully download and install the driver for your Jinka 1351

cutting plotter, you must match the driver to your specific model variant (Standard, Semi-Auto Contour, or Auto-Contour) Official Driver Download Links The most reliable source for Jinka drivers is Jinka Indonesia

. They provide direct links via Google Drive for various models: Jinka JK/XL Series (Cut Only)

: Best for standard JK1351 models without contour cutting features. Download Jinka JK/XL Driver Jinka XL Pro V (Auto Contour)

: Specifically for the "Pro V" versions equipped with automatic registration mark sensors. Download Jinka XL Pro V Driver General Download Repository

: A complete list of drivers for all models including PE, YS, and GC series is available at Jinka Indonesia Download Page Core Software & Plugins

Standard drivers allow your computer to recognize the device, but you also need cutting software to send designs: PlotCalc (CorelDRAW Plugin)

: Ideal for users who want to cut directly from CorelDRAW. Version XE-1351 and JK-1351PE are supported. Download PlotCalc for Jinka SignMaster / AnyCut

: Many Jinka 1351 units ship with these. If you have the license key, you can download the software directly from the SignMaster Official Site Installation Steps Extract Files : Drivers often come in a format. Use to extract them. : Open the folder and run as an Administrator. Port Selection

: During setup, you may be asked to choose a port. Jinka 1351 typically uses a USB-to-Serial emulation

: Reboot your computer to ensure the driver is fully integrated. Troubleshooting Common Issues Driver Not Recognized download driver cutting plotter jinka 1351 link

: Ensure the USB cable is plugged in before turning on the plotter. If it still fails, check "Device Manager" in Windows to see if it's listed under "Ports (COM & LPT)". Microsoft Learn Cutting Scale Issues

: If the cut size doesn't match your design, you may need to recalibrate the "actual cutting scale" within your cutting software settings. Communication Error

To get your Jinka 1351 cutting plotter running, you need to download the correct driver based on your specific model variant (Standard or Contour Cut). Download Links The official links for Jinka 1351 drivers are hosted via Jinka Indonesia: Standard (Only Cut): For Jinka XL PRO 1351

and JK models without contour features, use this Google Drive link. Contour Cut (Semi-Auto): For newer

or Pro 2 versions that support semi-auto contouring, use this Google Drive link. Auto Contour Cut: For or PE PRO models, use this Google Drive link. Key Features of the Jinka 1351 Series Jinka 1351

is a large-format vinyl cutter favored for its balance of cost and performance. Software for JinKa XE-1351 plotter - PlotCalc

Ultimate Guide: Download Driver Cutting Plotter Jinka 1351 (Direct Links & Setup)

If you’ve recently acquired a Jinka 1351 or are reinstalling your workstation, finding the right driver is the most critical step to getting your vinyl cutter running. The Jinka 1351 is a workhorse in the signage industry, but because it often uses a USB-to-Serial interface, Windows doesn't always recognize it automatically.

This guide provides the necessary links and a step-by-step walkthrough to get your plotter communicating with your PC. 1. Identify Your Connection Type Before downloading, check how your Jinka 1351 is connected:

USB Cable: Most users need the CH340 or PL2303 USB-to-Serial driver.

Serial Cable (9-pin): You generally do not need a driver for a direct DB9 serial connection; you simply need to configure the COM Port in your software (ArtCut, Flexi, or SignMaster). 2. Download Links for Jinka 1351 Drivers

Since Jinka uses universal USB chips, you can download the official drivers here:

USB Serial Driver (CH340/CH341): Download here via SparkFun or Official WCH Site. (This is the most common driver for Jinka machines).

Alternative USB Driver (PL2303): Download via Prolific. (Used in older Jinka models).

CorelDraw Plug-in: If you plan to cut directly from CorelDraw, you will need the Jinka CorelDraw Driver/Plug-in. 3. How to Install the Jinka 1351 Driver

Disconnect the Plotter: Unplug the USB cable from your computer.

Run the Installer: Open the .exe file you downloaded (likely CH341SER.exe).

Click Install: Wait for the "Driver install success" message. The Jinka 1351 cutting plotter driver download process

Connect the Plotter: Plug the USB cable back in and power on the Jinka 1351. Check Device Manager: Right-click the Start button > Device Manager. Look under Ports (COM & LPT).

You should see "USB-SERIAL CH340 (COM3)" or similar. Note the COM number. 4. Configuring Your Cutting Software

The driver only creates the "bridge." You still need to tell your software where to find the plotter.

Software: Select "Jinka" or "RedSail" (Jinka uses RedSail command sets). Model: 1351 (or 1350).

Port: Match this to the COM port found in your Device Manager (e.g., COM3). Baud Rate: Usually 9600 or 38400. Flow Control: Hardware or RTS/CTS. 5. Troubleshooting Common Issues

"Unable to open port": Ensure no other software (like a printer driver) is using that COM port. Try changing the COM port number in Device Manager to COM1 or COM2.

Garbage Characters/Random Lines: This is usually a Baud Rate mismatch. Ensure the Baud Rate on the physical plotter screen matches the setting in your software.

Windows 10/11 Driver Signature: If the driver fails to install, you may need to temporarily disable "Driver Signature Enforcement" in Windows recovery settings. Summary Table for Jinka 1351 Setup Setting/Value Driver Chip CH340 / CH341 Emulation RedSail / DMPL Baud Rate 9600 / 38400 Common Software ArtCut, SignMaster, AnyCut, FlexiStarter Need help with specific software?

Depending on your specific model variant, you may need a different driver: Jinka XL Pro 1351 (Only Cut) : Download Driver Jinka JK/XL Series (General Only Cut) : Download Driver Jinka XL Pro V 1353 (Auto Contour) : Download Driver Installation & Setup Guide

Preparation: Disconnect the plotter and any other USB devices (except your mouse/keyboard) before starting to avoid COM port conflicts.

Uninstall Old Drivers: Open Device Manager, expand Ports (COM & LPT), and uninstall any existing "USB Serial Port" or "Plotter Controller" entries.

Run as Administrator: Extract the downloaded ZIP file, right-click setup.exe, and select Run as Administrator.

Connect Plotter: Once installed, connect the USB cable and turn on the plotter. It should appear under Ports (COM & LPT) in Device Manager.

Assign COM Port: If the software doesn't detect it automatically, manually assign it to COM3 to avoid common conflicts with other hardware. Compatible Software Jinka 1351

typically comes with Jinka Cut free of charge. Other popular professional software options include: Driver Jinka 1351 28 - Facebook

REPORT: Driver Acquisition and Installation for Jinka 1351 Cutting Plotter

DATE: October 26, 2023 TO: User FROM: AI Assistant SUBJECT: Sourcing and Configuration of Jinka 1351 USB/Parallel Drivers REPORT: Driver Acquisition and Installation for Jinka 1351

I couldn’t find an official Jinka 1351 driver hosted by the manufacturer.
However, users have reported success with this driver package (for Windows 10/11, 64-bit):

👉 [Link placeholder – e.g., “Download Jinka 1351 Driver (ZIP, 4MB)”]
(You would insert your actual file link here – e.g., from Google Drive, Dropbox, or a trusted driver site like DriverGuide or CNCzone.)

If you have a verified safe link, please share it below.
Otherwise, try this generic HP-GL plotter driver built into Windows:

Looking for the Jinka 1351 cutting plotter driver? The Jinka 1351 is a compact, hardworking plotter popular with small sign shops and hobbyists for precise vinyl cutting and simple vector jobs. To get it running smoothly, you’ll want the correct driver matched to your OS — the right driver ensures accurate cutting paths, reliable USB/serial communication, and access to speed/pressure settings inside your design software.

Tips before downloading:

If you want, I can:

Which would you like me to do next?

(Invoking related search suggestions.)

Subject: Download Driver for Cutting Plotter Jinka 1351 – Working Link & Instructions

Post:

Hi everyone,

If you’re looking for the driver to get your Jinka 1351 cutting plotter up and running, here’s what you need to know.

⚠️ Important note: Official drivers for less common plotter brands like Jinka can be hard to find because manufacturer websites often go offline. Use caution when downloading from third-party sites.

The most reliable source for legacy plotter drivers is the SignTools or similar industry forums. These drivers are often repackaged to work with Windows 7, 10, and 11.

Finding a safe download driver cutting plotter Jinka 1351 link is easier when you know the alternatives. While the official ZIP is ideal, the HP DesignJet 750C driver works perfectly in 9 out of 10 cases. Always prefer direct manufacturer channels or the built-in Windows driver library over shady download sites.

Final recommendation: Bookmark this guide. Use the HP universal driver method first. If that fails, contact your Jinka supplier and ask for their “Jinka 1351 Windows driver package (64-bit).”

Need further help? Leave a comment on sign-making forums like Signs101 or r/VinylCutters on Reddit – many Jinka 1351 owners share their driver links there.