Remote: How Do I Reset My Parrot Mki9200 Without
If your unit is completely frozen (no screen response, no sound) and the pin-hole does nothing, you need to physically cut all power.
Step 1: Locate the MKi9200’s Fuse The MKi9200 is almost always connected to your car's fuse box using a "piggyback" fuse holder or an inline fuse. You need to find which fuse powers the kit. Check your car’s fuse box diagram (usually in the owner’s manual or on the fuse box cover) for any fuse labeled "Hands-free," "Telephone," or a non-standard accessory.
Step 2: Remove the Fuse Using your car's fuse puller or a pair of pliers, carefully pull the fuse that supplies power to the Parrot kit. Wait for 60 seconds to allow all capacitors inside the MKi9200 to fully discharge.
Step 3: Reinsert the Fuse Place the fuse back into its slot firmly.
Step 4: Turn on the Ignition Power on your car's electrical system. The Parrot MKi9200 should now perform a cold boot and restart as if it were new.
If you truly need a full factory reset and cannot find the remote:
Without the remote or a firmware reinstall, you are limited to clearing only the Bluetooth memory. For most users, that is enough to sell the car or connect a new phone.
How to Reset a Parrot MKi9200 Without a Remote The Parrot MKi9200
is designed to be controlled almost entirely through its wireless remote. If your remote is lost or broken, performing a standard factory reset—which usually requires navigating the on-screen menus—is difficult but not impossible through alternative manual methods. 1. The Hard Reboot (Power Cycling)
The simplest way to clear temporary glitches without a remote is a hard reboot. This does not delete your paired devices but can resolve "frozen" screens or connection issues.
Disconnect Power: Locating and disconnecting the main blue control box from the car's wiring for about one hour can force the system to reboot.
Battery Disconnect: Alternatively, you can disconnect the vehicle's battery for a similar period to achieve a system-wide reset. 2. Manual Clear (Memory Full Fix)
If you are trying to reset because of a "Memory Full" error, there is a specific button combination that can wipe saved data without navigating menus. This is often necessary when you cannot pair new devices.
The "3-Button" Press: While the unit is powered on, press and hold the Green, Red, and Center Jog Wheel buttons simultaneously for approximately 10 seconds.
Confirmation: If successful, the screen should go blank and emit a beep, indicating that all saved data and paired devices have been wiped. 3. Software Update Reset how do i reset my parrot mki9200 without remote
Performing a firmware update via the USB port can sometimes reset the device to factory defaults as part of the installation process.
USB Update: You can download the update tool from the Parrot Software Update page and load the update files onto a USB stick.
Automatic Detection: In some cases, plugging the USB stick into the
's music cable will trigger an update prompt automatically, though this often still requires a remote "click" to confirm. 4. Steering Wheel Control Alternative
If your vehicle has a steering wheel interface (like the Parrot UNIKA) installed, you may be able to use your car's existing buttons to navigate the menu to Settings > Advanced Settings > Factory Settings. Summary of Reset Options Method Requirement Hard Reboot Clears temporary errors Physical access to control box or car battery 3-Button Hold Wipes all paired devices Access to the screen buttons Firmware Flash Reinstalls system software USB stick and PC
Parrot MKi9200 Remote Not Connecting How To Fix? - JustAnswer
How to Reset Your Parrot MKi9200 Without Remote: A Step-by-Step Guide
Are you struggling to reset your Parrot MKi9200 Bluetooth car stereo system because you've lost or misplaced the remote control? Worry no more! In this article, we'll walk you through a step-by-step guide on how to reset your Parrot MKi9200 without a remote. We'll also cover some troubleshooting tips and provide additional information to help you get the most out of your device.
Why Reset Your Parrot MKi9200?
Before we dive into the reset process, let's discuss why you might need to reset your Parrot MKi9200 in the first place. Resetting your device can help resolve various issues, such as:
Resetting your Parrot MKi9200 will restore the device to its factory settings, which can often resolve software-related problems.
How to Reset Your Parrot MKi9200 Without Remote
Resetting your Parrot MKi9200 without a remote requires a combination of button presses on the device itself. Here's the step-by-step process:
Alternative Method
If the above method doesn't work, try the following alternative:
Troubleshooting Tips
If you're still experiencing issues with your Parrot MKi9200 after resetting it, here are some troubleshooting tips:
Additional Tips and Information
Conclusion
How to Reset Your Parrot MKi9200 Without a Remote If you have lost your remote control or the battery has died, you might find yourself locked out of your Parrot MKi9200 settings. Because this system relies almost entirely on its wireless RF remote for menu navigation, performing a factory reset without it is difficult—but not impossible if you have the right hardware or a bit of patience. The Short Answer: Can You Reset Without a Remote?
Standard factory resets for the Parrot MKi9200 strictly require the remote control to access the Settings > Advanced Settings > Factory Reset menu. However, there are two primary workarounds depending on your car's setup:
Steering Wheel Controls (Unika Interface): If your car uses the Parrot Unika interface to link your steering wheel buttons to the Parrot system, you can navigate the menus without the original remote.
Hard Reboot (Battery Disconnect): While not a "factory reset" that wipes data, disconnecting the unit from power for one hour can resolve some software glitches and "reboot" the system. Method 1: Using the Unika Steering Wheel Interface
If your installer integrated the Parrot system with your car’s factory steering wheel buttons, you can use a specific sequence to enter the menu and trigger a reset.
Enter the Menu: Rapidly press the following sequence on your steering wheel: Track Forward > Track Back > Track Forward > Track Back.
Navigate to Settings: Once the menu appears on the MKi9200 screen, use the Track Forward button to scroll until you see "Settings".
Access Advanced Settings: Press your steering wheel's Phone/Accept button to enter the menu. Scroll down to "Advanced Settings" and press Phone/Accept again.
Trigger Factory Reset: Navigate to Factory Reset and confirm with the Phone/Accept button. The unit will reboot and clear its memory. Method 2: The "Memory Full" Emergency Reset If your unit is completely frozen (no screen
If you are trying to reset because you see a "Memory Full" error and cannot pair new phones, some users have reported success with a physical button combination if they still have access to the screen's control box or older firmware versions.
The Command: Press and hold the Green (Answer), Red (End Call), and Center Jog Wheel (if your model has an integrated one) buttons simultaneously for approximately 10 seconds.
The Result: The screen should go blank and emit a beep, indicating that the paired device list has been wiped. Method 3: Troubleshooting a "Dead" Remote
Before giving up on the remote, check if it simply needs a re-sync rather than a full system reset. Often, a remote isn't "broken," it just lost its pairing with the blue electronic box.
Replace the Battery: The remote uses a standard CR2032 battery. Ensure it is inserted correctly and that the metal contacts are touching the battery. Re-pair the Remote: Turn on your car's ignition.
Within the first 2 minutes of boot-up, simultaneously press and hold the Answer (Green), End (Red), and Play/Pause buttons.
Continue pressing them until the screen displays "Pairing Remote". Pro-Tips for Persistent Issues
Wiring Check: If your Parrot forgets settings every time you turn off the car, it likely isn't a reset issue but a wiring problem. You may need to swap the red and orange wires on the Parrot harness to ensure the unit receives constant power for its memory.
Replacement Parts: If the remote is truly lost, note that official replacements are increasingly rare. You may find used units on marketplaces like eBay or specialized retailers like JustCarKits.
Do you have steering wheel buttons available, or are you looking to buy a replacement remote to regain control? JustCarKitshttps://www.justcarkits.co.uk
How to reset a Parrot MKi9200 without the remote - JustCarKits
Keep holding the button while watching the Parrot screen. After a few seconds, the screen should change.
The Parrot MKi9200 is a robust Bluetooth car kit, but like any electronic device, it can freeze, fail to pair, or develop audio glitches. The standard method to fix this involves using the remote control to access the settings menu.
If you have lost your remote or it has broken, you cannot perform a software-based reset via the on-screen menu. However, you can perform a hardware (factory) reset. This will erase all paired phones, the phonebook, and custom settings, returning the unit to its out-of-the-box state. If you truly need a full factory reset
Warning: This process will delete all your data on the MKi9200. Proceed only if you are willing to lose your saved pairings and settings.
If you have tried the wired control pad, the paperclip reset, and the power cycle, but your Parrot MKi9200 still won’t reset or respond, the internal memory may be corrupted beyond software recovery. In this case: