Note: The following steps are generic for MTK devices like the Benco V90. Always refer to the specific instructions included with your downloaded firmware file.
Use Flashing Tool:
Wait for the Process to Complete: This can take a few minutes. Once it's done, you should see a success message.
Reboot Your Device: After flashing, reboot your device. It might take a bit longer than usual to boot up.
Note: Flashing firmware carries a risk of voiding your warranty or damaging the device if done incorrectly. Proceed at your own risk.
Step 1: Extract the Files Download the Lava Benco V90 flash file and extract it using WinRAR or 7-Zip on your desktop. You should see the scatter file inside the folder.
Step 2: Launch SP Flash Tool
Open the SP Flash Tool folder and run flash_tool.exe as Administrator.
Step 3: Load the Scatter File In the SP Flash Tool interface, click on the "Choose" or "Scatter-loading" button. Navigate to the folder where you extracted the firmware and select the scatter file.
Step 4: Configure for Hang Logo Fix For a Hang Logo issue, it is generally recommended to use the "Firmware Upgrade" or "Download Only" option. lava benco v90 ae9120 flash file s160 hang logo new
Step 5: Connect the Device Turn off the Lava Benco V90 completely. In the SP Flash Tool, click the "Download" button. Now, connect the switched-off phone to the PC via USB.
Step 6: Flashing Process If the drivers are installed correctly, the tool should detect the phone, and a progress bar will appear. Wait for the process to reach 100%.
Step 7: Completion Once finished, you will see a green circle with a "Download Ok" message. Disconnect the phone, insert the battery (if removed), and power it on. The first boot may take 3-5 minutes as the system rebuilds the cache.
Related search suggestions incoming.
Lava Benco V90 (AE9120) that is hanging on the logo or stuck in a boot loop, you must flash the official stock firmware
. This process repairs software-related issues, including "dead boot" scenarios and recovery mode errors. Essential Preparation Battery Charge : Ensure the device has at least 50% battery to prevent it from turning off during the flash. Data Backup : Flashing will erase all user data . Back up anything important if the device allows access. : Install the latest Spreadtrum (SPD) USB Drivers on your PC so the computer recognizes the phone. Flash File Details Lava Benco V90 (AE9120) Build Version (New Version) : 100% Tested and verified to fix logo-hanging issues. Flashing Steps Download the Firmware : Obtain the tested Lava Benco V90 AE9120 S160 flash file from reliable sources like Flashfile Bazar or verified YouTube community links Extract the Files
: Use a tool like WinRAR or 7-Zip to extract the downloaded firmware and the flash tool (usually SPD Upgrade Tool ResearchDownload Load the File : Open the flash tool, click the "Load Packet" (gear icon), and select the file from the firmware folder. Connect the Device Turn off the phone completely. Volume Down (or Volume Up + Down) button. Connect the phone to the PC via a USB cable. Start Flashing : Once the tool detects the device, click the (Play) button. The process usually takes 3–5 minutes. : After the tool shows a green
The story of the Lava Benco V90 (specifically the AE9120 and S160 variants) is one well-known to mobile technicians—a tale of a "digital coma" followed by a high-stakes surgical revival using a Flash File. The Conflict: The Dreaded "Hang Logo" Note: The following steps are generic for MTK
It begins with a user reaching for their Benco V90, expecting to see their home screen. Instead, they are met with a stubborn, glowing logo that refuses to move. This is the "Hang Logo"—a state where the phone’s software is corrupted, stuck in a boot loop, or completely unresponsive (dead boot).
For the V90, an entry-level powerhouse with a Unisoc SC9863A processor and a massive 6.82-inch display, this freeze often happens due to:
System Crashes: A failed update or corrupted system partition on its Android 12 OS.
Memory Overload: Despite its 4GB RAM, heavy multitasking can sometimes push the entry-level chipset too far. The Solution: The Digital Scalpel
The "hero" of this story is the Flash File (Stock ROM). To fix a Benco V90 AE9120 or stuck on the logo, technicians perform a "Flash". The Resurrection Process: Preparation: The technician downloads the specific Lava Benco V90 AE9120
/ S160 Flash File—a 100% tested firmware package designed to overwrite the corrupted system.
Fastboot Mode: The phone is put into Fastboot or Recovery Mode.
The Flash: Using a PC and a USB cable, the firmware is injected into the phone's internal storage. Configure Settings:
The Reboot: After the flash_all.bat script finishes, the tension peaks. The phone vibrates, the logo appears—but this time, it fades into the familiar Android setup screen. The Outcome: New Life Once the flash is complete, the
is effectively "new" again. All software errors are wiped clean, the 5000mAh battery can finally power a working system, and the 16MP AI triple camera is ready to snap photos once more.
If you are looking to perform this repair, ensure you have the correct drivers and a verified firmware file to avoid "hard bricking" the device.
Do you need a step-by-step guide on how to use a flashing tool?
Is your phone currently in Fastboot mode or completely black (dead)?
It sounds like you’re dealing with a Lava Benco V90 (AE9120) that’s stuck on the logo after flashing, and you’re looking for a working flash file (firmware) to fix the “hang on logo” issue.
Here’s what you likely need and some troubleshooting steps: