RAPTOR is a flowchart-based programming environment, designed specifically to help students visualize their algorithms and avoid syntactic baggage. RAPTOR programs are created visually and executed visually by tracing the execution through the flowchart. Required syntax is kept to a minimum. Students prefer using flowcharts to express their algorithms, and are more successful creating algorithms using RAPTOR than using a traditional language or writing flowcharts without RAPTOR.
Are you interested in running RAPTOR on Chromebooks, iPads, or just in a browser? Check out the pre-release here!. This is NOT fully tested. Send feedback via
A Multiplatform version of RAPTOR is now available for Windows, Mac and Linux built on top of [Avalonia]! See the downloads section below. Uses fonts from Noto Sans CJK for internationalization. Key differences:
Figure 1 RAPTOR for Windows
Figure 2 RAPTOR Avalonia
Papers on RAPTOR application:
RAPTOR referenced in following books or publications:
 |
 |
 |
The MDF file format is the industry standard for recording measurement data in automotive development. Version 7.3.5 likely refers to a specific iteration of the MDF library or toolchain (such as the open-source MDF library) used to read/write these files. The "UFI" block is a critical component introduced to handle files that were not closed properly (e.g., due to a power loss or crash).
Authentic UFI-V7.3.5 programmers are sold through authorized distributors (listed on the official UFI website). Avoid clones—they often come with dated V6.x firmware that cannot be updated and may damage ECUs due to improper voltage regulation.
Pricing typically ranges from $250 to $350 USD, including the main unit, a USB cable, one 10-pin IDC probe, and a set of pin adapters. A worthwhile bundle includes the "All-in-One" clip set (for SOIC8 and SOP8 chips) and a logic analyzer probe.
Customer support for UFI-V7.3.5 is primarily community-driven via dedicated forums and Telegram groups, though official email support is available for hardware RMA.
The physical UFI-V7.3.5 programmer is a marvel of engineering efficiency. It connects to a host PC via a high-speed USB 2.0/3.0 interface, ensuring rapid data transfers even for large firmware files. Key hardware features include:
Compared to its predecessor (UFI-V6.x), the V7.3.5 boasts a 40% increase in programming speed for large NOR flash chips and improved noise isolation for reliable reads in electrically noisy shop environments.
The MDF file format is the industry standard for recording measurement data in automotive development. Version 7.3.5 likely refers to a specific iteration of the MDF library or toolchain (such as the open-source MDF library) used to read/write these files. The "UFI" block is a critical component introduced to handle files that were not closed properly (e.g., due to a power loss or crash).
Authentic UFI-V7.3.5 programmers are sold through authorized distributors (listed on the official UFI website). Avoid clones—they often come with dated V6.x firmware that cannot be updated and may damage ECUs due to improper voltage regulation. ufi-v7.3.5
Pricing typically ranges from $250 to $350 USD, including the main unit, a USB cable, one 10-pin IDC probe, and a set of pin adapters. A worthwhile bundle includes the "All-in-One" clip set (for SOIC8 and SOP8 chips) and a logic analyzer probe. The MDF file format is the industry standard
Customer support for UFI-V7.3.5 is primarily community-driven via dedicated forums and Telegram groups, though official email support is available for hardware RMA. Compared to its predecessor (UFI-V6
The physical UFI-V7.3.5 programmer is a marvel of engineering efficiency. It connects to a host PC via a high-speed USB 2.0/3.0 interface, ensuring rapid data transfers even for large firmware files. Key hardware features include:
Compared to its predecessor (UFI-V6.x), the V7.3.5 boasts a 40% increase in programming speed for large NOR flash chips and improved noise isolation for reliable reads in electrically noisy shop environments.
Do you want more older versions? Check out older versions of RAPTOR here
Did you know RAPTOR has modes? By default, you start in Novice mode. Novice mode has a single global namespace for variables. Intermediate mode allows you to create procedures that have their own scope (introducing the notion of parameter passing and supports recursion). Object-Oriented mode is new (in the Summer 2009 version)
RAPTOR is freely distributed as a service to the CS education community. RAPTOR was originally developed by and for the US Air Force Academy, but its use has spread and RAPTOR is now used for CS education in over 30 countries on at least 4 continents. Martin Carlisle is the primary maintainer, and is a professor at Texas A&M University.
Below handouts are by Elizabeth Drake, edited from Appendix D of her book, Prelude to Programming: Concepts and Design, 5th Edition, by Elizabeth Drake and Stewart Venit, Addison-Wesley, 2011. Linked here with author's permission.
Comments, suggestions, and bug reports are welcome. If you have a comment, suggestion or bug report, send an email to .
David Cox has put together a user forum at http://raptorflowchart.freeforums.org. This provides a place for users to exchange ideas, how tos, etc. Note however, that feedback for the author should be sent by email rather than posting on this forum.
Randy Bower has some YouTube tutorials at http://www.youtube.com/user/RandallBower. You can also search YouTube for "RAPTOR flowchart".
The UML designer is based on NClass, an open-source UML Class Designer. NClass is licensed under the GNU General Public License. The rest of RAPTOR, by US Air Force policy, is public domain. Source is found here. RAPTOR is written in a combination of A# and C#. Unfortunately, I don't have the time to provide support on compilation issues