Mks Laser Tool Setup V112exe Download Better May 2026
To set up the MKS Laser Tool V1.1.2, download the official executable file directly from the authorized Makerbase GitHub repository or their official website to ensure file safety.
Below is a complete guide to downloading, installing, and configuring the software for your laser engraving machine. 📥 Step 1: Securely Download the Software Avoid third-party download sites to prevent malware. Official Source: Visit the Makerbase GitHub Repository.
Direct File: Look for MKS Laser Tool V1.1.2.exe in the releases or software folder.
Backup Source: Check the official Makerbase website support section. ⚙️ Step 2: Installation Process Installing the tool takes less than two minutes.
Run as Admin: Right-click the .exe file and select Run as administrator.
Driver Prompt: Allow the installer to add necessary CH340 USB drivers. Finish: Complete the wizard and launch the application. 🔌 Step 3: Connecting Your Hardware
Establish a stable connection between your PC and the MKS motherboard.
USB Link: Connect your PC to the MKS board using a high-quality USB cable. Power On: Ensure your laser machine is powered on.
Port Selection: Open the software and select the correct COM Port.
Baud Rate: Set the speed (usually 115200) and click Connect. 🛠️ Step 4: Key Features & Usage
The MKS Laser Tool is divided into several functional modules.
🖼️ Image Conversion: Transform JPG/PNG files into laser-ready G-code.
🌐 WiFi Configuration: Set up ESP32 WiFi networks for wireless engraving. mks laser tool setup v112exe download better
⬆️ Firmware Flashing: Update your physical board with the latest GRBL firmware.
💡 Pro-Tip: Always keep a backup of your original firmware before flashing any new updates to the board!
The MKS Laser Tool Setup V1.1.2.exe is a specialized Windows-based utility developed by Makerbase for managing laser engravers, specifically those using MKS Robin or DLC32 series motherboards. Core Deep Features
Firmware Management: The primary use for version 1.1.2 is flashing and upgrading firmware for laser engravers like the Two Trees TTS Pro. It allows you to erase old firmware and install new .bin files tailored to your machine's hardware version (1.0 or 2.0).
WiFi Configuration: It acts as a bridge to connect your laser engraver to your home network. You can set the SSID and password via a USB connection, allowing for later wireless control without needing a touchscreen.
G-Code Modification & Preview: The tool can preview G-code and modify files to add essential positioning codes, ensuring the laser head starts at the correct origin.
Machine Adaptation: Users can import specific machine configuration files directly into the motherboard, simplifying the setup of motor steps, moving speeds, and homing behaviors.
Graphical Interface for UI: While it supports firmware, it is also designed to visually customize the user interface on compatible MKS touchscreen displays. Essential Technical Tips
Administrator Mode: If buttons appear unclickable or the app seems frozen, users recommend closing the program and selecting "Run as Administrator".
Power Requirements: When connecting via USB to a PC, the motherboard must be powered by an external 12–24V supply; the USB port alone does not provide enough power for the board to be recognized.
Driver Installation: For first-time connections, you must install the CH340 USB driver to allow your PC to identify the COM port. Official & Safe Downloads
To ensure a secure installation, it is best to source the tool from official developer repositories: To set up the MKS Laser Tool V1
How to use the MKS Laser Tool if it you can't click on the buttons.
The MKS Laser Tool V1.1.2 is a utility software developed by Makerbase for managing laser engraving machines, specifically those using MKS DLC32 motherboards. The Mks Laser Tool Setup V1.1.2.exe file is the installer for this Windows-based application. Core Features of MKS Laser Tool
The software serves as a bridge between your computer and the engraving hardware, offering several key functions:
Firmware Updates: Allows users to flash new firmware to ESP32-based boards like the DLC32.
WiFi Configuration: Provides a dedicated tool to set up the engraver’s network settings (SSID and password) so it can be controlled wirelessly via IP.
G-Code Modification: Includes utilities to preview G-code and add positioning or cooling fan commands.
Parameter Management: Facilitates importing and exporting machine settings directly to the board. Setup and Download Instructions
makerbase-mks/MKS-TOOL: MKS TOOL is a tool that ... - GitHub
MKS Laser Tool (v1.1.2) is a specialized utility primarily used for configuring Wi-Fi and flashing firmware on laser engraving machines equipped with Makerbase MKS DLC32
motherboards. While it is a essential for certain hardware setups, it is known for having a steep learning curve and several technical quirks. Key Features Firmware Flashing
: Used to upgrade or restore firmware on compatible laser engravers like those from Flying Bear Wi-Fi Configuration
: Allows users to connect their laser engraver to a local network to enable wireless control via the mobile app. Motherboard Customization | Source | URL / Method | Reliability
: Part of the broader MKS TOOL suite, it can be used to modify display UIs and configuration files for supported boards. User Experience & Reviews Reviewers from platforms like highlight both the tool's utility and its frustrations: Essential for Wireless
: Many users find it successful for setting up Wi-Fi, which then allows for convenient smartphone control via the MKSLaser App Versatile Hardware Support
: Works across various MKS series boards, including the popular DLC32. Installation Hurdles
: The installer interface is often entirely in Chinese, requiring users to navigate by memory or "guess" the correct buttons (typically the middle option). Functionality Issues
: A common bug involves buttons being "unclickable" after launch. The standard community fix is to Run as Administrator Stability Risks
: Flashing the wrong firmware version can "brick" or disable the engraver, leading to unresponsive hardware or constant error beeps. Final Verdict MKS DLC32 WIFI CNC Control Board Review
this is the new MKS DLC32 CNC control board from Makeabase. you can use this board to control your CNC machine wirelessly over Wi- Superb Tech
How to use the MKS Laser Tool if it you can't click on the buttons.
This is a comprehensive guide to setting up the MKS Laser Tool (specifically the V1.1.2 variant) for 3D printers (typically Ender 3 or similar Creality machines).
Since the specific filename v112exe usually refers to the MKS Laser Tool Host Software (used to control the laser from your PC), this guide focuses on installing that software correctly, configuring the firmware, and ensuring you get better results than the default setup.
| Source | URL / Method | Reliability |
|--------|--------------|--------------|
| GitHub (MKS official) | Search “MKS-Laser-Tool” → Releases → find v1.12 .exe | ⭐⭐⭐⭐⭐ |
| MKS Wiki / ESP3D | mks.wiki → Products → DLC32 → Software | ⭐⭐⭐⭐ |
| LightBurn forums | Community shared links (always verify hash) | ⭐⭐⭐ |
| BIGTREETECH GitHub | MKS is a sister brand; sometimes hosted there | ⭐⭐⭐⭐ |
✅ Preferred:
Direct GitHub example (verify at time of reading):
https://github.com/makerbase-mks/MKS-Laser-Tool/releases/tag/v1.12
If you are looking for "better" quality engravings, the .exe version won't help. Quality comes from settings: